Webb Is Chilling Out

While we have started the long process of aligning the telescope mirrors, almost all of the components on Webb’s cold side are still continuing to cool.

Webb’s giant sunshield keeps the telescope and cameras out of both direct sunlight and sunlight that is reflected from Earth and the Moon. Everything on the cold side of the sunshield is passively cooling, radiating heat into deep space. That will continue until the telescope and the three near-infrared (NIR) instruments reach a steady-state temperature, where the milliwatts of energy that get through the sunshield, plus heat generated by the instruments’ own electronics, exactly balances the loss of heat into space. We expect that the primary mirror will cool to below 50 kelvins (about -370 degrees Fahrenheit, or -223 degrees Celsius), and the NIR instruments will reach about 40 kelvins (about -388 degrees Fahrenheit, or -233 degrees Celsius).

Webb’s Mid-Infrared Instrument (MIRI) needs to be even colder. In addition to passive cooling, MIRI will be cooled by a closed-cycle gaseous-helium cryocooler, or refrigerator, down to a temperature below 7 kelvins (-447 degrees Fahrenheit, or -266 kdegrees Celsius). Unlike some previous cryogenic missions, which were cooled by boiling off liquid helium and venting it into space, MIRI’s cooler reuses its helium, just like the refrigerator in your kitchen continuously recycles its own coolant. The Webb team turned on the first stage of the MIRI cryocooler this week.

Primary Mirror Segment Assembly (PMSA) and Secondary Mirror Assembly (SMA) temperatures, as of Wednesday, Feb. 9. Credit: NASA

In the several weeks since Webb’s sunshield was deployed, Webb’s mirrors have been cooling, but they aren’t at their final temperatures yet. There is a variation of temperatures across the different segments, and the segments closer to the sunshield and spacecraft bus are warmer. We expect that these mirror segments will all cool by another 10 kelvins or so, but their final temperatures will still have a spread of 15 to 20 kelvins. The secondary mirror, hanging out on the end of its “spider” support structure, is already very cold.

Meanwhile, the NIR instruments are also cooling. Early in the cooldown process, the Webb team used heaters to keep the instruments warmer than the cold-side structures, to prevent water ice from forming on the optical surfaces. But that is all done now, and the instruments and their detectors are cooling nicely. Their current temperatures are about 75 kelvins (-325 degrees Fahrenheit, or -198 degrees Celsius); they will continue to cool for a few more weeks before reaching their final operating temperature.

The cooling of an infrared telescope is a precise and critical process to ensure the success of the instrumentation and, ultimately, the amazing science. We have learned from and improved upon many years of infrared missions. Webb’s historian, Robert W. Smith, explains a bit more about how Webb builds on the legacy of previous infrared observatories:

“Pioneering investigators examined various astronomical objects in the infrared from the year 1800 on. Infrared astronomy, however, began to take off only in the 1960s. Given the limitations imposed by the atmosphere, researchers experimented with telescopes on balloons and rockets.

“Nevertheless, the grand prize was an infrared telescope in space not limited to the five or so minutes observing time of a rocket flight. Efforts in the U.S., the Netherlands, and the United Kingdom led to the Infrared Astronomy Satellite (IRAS). Launched in 1983, IRAS surveyed the skies at a range of wavelengths and, during its ten-month lifetime, identified 350,000 infrared sources. The Infrared Space Observatory (ISO) followed IRAS in 1995. It became the first infrared space telescope to exploit arrays of detectors of the sort that had begun to revolutionize ground-based infrared astronomy in the years around 1990.

“Critical for the future of infrared space telescopes was the radical shift to radiative or passive cooling. The mirrors of infrared telescopes emit infrared radiation, and to observe the infrared signals emitted by astronomical sources, many of which are exceedingly faint, the mirrors need to be kept very cold. Both IRAS and ISO had kept their telescopes cold by placing them inside a Dewar filled with liquid helium. But adopting this approach seriously limited the size of the telescope that could fly. Tim Hawarden of the Royal Observatory, Edinburgh, began in the early 1980s to explore the idea of doing away with the Dewar. Instead, a telescope would be launched warm and cooled by radiating heat away to space.

“The first infrared space telescope to use passive cooling was NASA’s Spitzer Space Telescope, launched in 2003 into an Earth-trailing orbit. The primary mirror cooled passively to about 34 kelvins before liquid helium was used to get the observatory to less than 6 kelvins. The Herschel Space Observatory, an ESA (European Space Agency) project, had a passively cooled primary mirror (to 80 kelvins) with liquid helium cooled instruments. Herschel operated from 2009 to 2013 and orbited around the L2 Lagrange point, similar to Webb. Herschel’s 3.5-meter diameter mirror made it the largest infrared telescope before Webb.

“In 1989, at a workshop at the Space Telescope Science Institute, astronomers explored ideas for the ‘Next-Generation U-V-Visible-IR Telescope’ to succeed Hubble. These discussions led to the suggestion of an infrared optimized telescope, the ‘Next Generation Space Telescope,’ the vision of which was realized in the world’s largest and most powerful infrared observatory: Webb.”

-Robert W. Smith, professor of history, University of Alberta

Check back tomorrow for an exciting update about progress in the first weeks of Webb’s mirror alignment!

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Alexandra Lockwood, project scientist for Webb science communications, Space Telescope Science Institute

Photons Incoming: Webb Team Begins Aligning the Telescope

This week, the three-month process of aligning the telescope began – and over the last day, Webb team members saw the first photons of starlight that traveled through the entire telescope and were detected by the Near Infrared Camera (NIRCam) instrument. This milestone marks the first of many steps to capture images that are at first unfocused and use them to slowly fine-tune the telescope. This is the very beginning of the process, but so far the initial results match expectations and simulations.

A team of engineers and scientists from Ball Aerospace, Space Telescope Science Institute, and NASA’s Goddard Space Flight Center will now use data taken with NIRCam to progressively align the telescope. The team developed and demonstrated the algorithms using a 1/6th scale model telescope testbed. They have simulated and rehearsed the process many times and are now ready to do this with Webb. The process will take place in seven phases over the next three months, culminating in a fully aligned telescope ready for instrument commissioning. The images taken by Webb during this period will not be “pretty” images like the new views of the universe Webb will unveil later this summer. They strictly serve the purpose of preparing the telescope for science.

To work together as a single mirror, the telescope’s 18 primary mirror segments need to match each other to a fraction of a wavelength of light – approximately 50 nanometers. To put this in perspective, if the Webb primary mirror were the size of the United States, each segment would be the size of Texas, and the team would need to line the height of those Texas-sized segments up with each other to an accuracy of about 1.5 inches.

Scott Acton and Chanda Walker of Ball Aerospace, along with Lee Feinberg of NASA Goddard, walk through the basic steps below:

“With deployment of the mirror segments now complete, and the instruments turned on, the team has begun the numerous steps required to prepare and calibrate the telescope to do its job. The telescope commissioning process will take much longer than previous space telescopes because Webb’s primary mirror consists of 18 individual mirror segments that need to work together as a single high-precision optical surface. The steps in the commissioning process include:

      1. Segment Image Identification
      2. Segment Alignment
      3. Image Stacking
      4. Coarse Phasing
      5. Fine Phasing
      6. Telescope Alignment Over Instrument Fields of View
      7. Iterate Alignment for Final Correction
1. Segment Image Identification

First, we need to align the telescope relative to the spacecraft. The spacecraft is capable of making extremely precise pointing moves, using “star trackers.” Think of star trackers as a GPS for spacecraft. At first, the position of the spacecraft from the star trackers does not match the position of each of the mirror segments.

We are pointing the telescope at a bright, isolated star (HD 84406) to capture a series of images that are then stitched together to form a picture of that part of the sky. But remember, we don’t have just one mirror looking at this star; we have 18 mirrors, each of which is initially tilted towards a different part of the sky. As a result, we’ll actually capture 18 slightly shifted copies of the star – each one out of focus and uniquely distorted. We refer to these initial star-copies as “segment images.” In fact, depending on the starting positions of the mirrors, it may take multiple iterations to locate all 18 segments in one image.

Simulated example of a possible initial deployment showing 18 segment images. Credit: NASA

One by one, we will move the 18 mirror segments to determine which segment creates which segment image. After matching the mirror segments to their respective images, we can tilt the mirrors to bring all the images near a common point for further analysis. We call this arrangement an “image array.”

2. Segment Alignment

After we have the image array, we can perform Segment Alignment, which corrects most of the large positioning errors of the mirror segments.

We begin by defocusing the segment images by moving the secondary mirror slightly. Mathematical analysis, called Phase Retrieval, is applied to the defocused images to determine the precise positioning errors of the segments. Adjustments of the segments then result in 18 well-corrected “telescopes.” However, the segments still don’t work together as a single mirror.

3. Image Stacking

To put all of the light in a single place, each segment image must be stacked on top of one another. In the Image Stacking step, we move the individual segment images so that they fall precisely at the center of the field to produce one unified image. This process prepares the telescope for Coarse Phasing.

The stacking is performed sequentially in three groups (A-segments, B-segments, and C-segments).

Credit: NASA
Simulation of image stacking. First panel: Initial image mosaic. Second panel: A-segments stacked. Third panel: A- and B-segments stacked. Fourth panel: A-, B-, and C-segments stacked. Credit: NASA.
4. Coarse Phasing

Although Image Stacking puts all the light in one place on the detector, the segments are still acting as 18 small telescopes rather than one big one. The segments need to be lined up with each other with an accuracy smaller than the wavelength of the light.

Conducted three times during the commissioning process, Coarse Phasing measures and corrects the vertical displacement (piston difference) of the mirror segments. Using a technology known as Dispersed Fringe Sensing, we use NIRCam to capture light spectra from 20 separate pairings of mirror segments. The spectrum will resemble a barber pole pattern with a slope (or angle) determined by the piston difference of the two segments in the pairing.

In this simulation, the “Barber pole” patterns are created by the Disperse Fringe Sensor indicating a large piston error (top) or a small piston error (bottom). Credit: NASA
5. Fine Phasing

Fine Phasing is also conducted three times, directly after each round of Coarse Phasing, and then routinely throughout Webb’s lifespan. These operations measure and correct the remaining alignment errors using the same defocusing method applied during Segment Alignment. However, instead of using the secondary mirror, we use special optical elements inside the science instrument which introduce varying amounts of defocus for each image (-8, -4, +4, and +8 waves of defocus).

A simulation of the defocused images used in Fine Phasing. The images (top) show defocus introduced to an almost aligned telescope. The analysis (bottom) indicates the errors associated with each telescope segment. Segments with very bright or dark colors need larger corrections. Credit: NASA
6. Telescope Alignment Over Instrument Fields of View

After Fine Phasing, the telescope will be well aligned at one place in the NIRCam field of view. Now we need to extend the alignment to the rest of the instruments.

In this phase of the commissioning process, we make measurements at multiple locations, or field points, across each of the science instruments, as shown below. More variation in intensity indicates larger errors at that field point. An algorithm calculates the final corrections needed to achieve a well-aligned telescope across all science instruments.

Simulated analysis of the Field of View correction. Credit: NASA
7. Iterate Alignment for Final Correction

After applying the Field of View correction, the key thing left to address is the removal of any small, residual positioning errors in the primary mirror segments. We measure and make corrections using the Fine Phasing process. We will do a final check of the image quality across each of the science instruments; once this is verified, the wavefront sensing and controls process will be complete.

As we go through the seven steps, we may find that we need to iterate earlier steps as well. The process is flexible and modular to allow for iteration. After roughly three months of aligning the telescope, we will be ready to proceed to commissioning the instruments.”

—Scott Acton, Webb lead wavefront sensing and control scientist, Ball Aerospace; Chanda Walker, Webb wavefront sensing and control scientist, Ball Aerospace; and Lee Feinberg, Webb optical telescope element manager, NASA’s Goddard Space Flight Center

Following Webb’s Arrival at L2, Telescope Commissioning Set to Begin

Following Webb’s arrival at its orbital destination around Lagrange Point 2 (L2) on Jan. 24, the mission operations team began working its way through a critical series of steps: powering on all the science instruments, turning off heaters to begin a long cooldown process, and ultimately capturing the first photons on Webb’s primary camera to enable a months-long alignment of the telescope.

While the MIRI instrument and some instrument components were powered on in the weeks after Webb’s Dec. 25 launch, the team didn’t finish turning on the remaining three instruments – NIRCam, NIRSpec, and FGS/NIRISS – until the past few days.

The mission operations team’s next major step is to turn off instrument heaters. The heaters were necessary to keep critical optics warm to prevent the risk of water and ice condensation. As the instruments meet pre-defined criteria for overall temperatures, the team is shutting off these heaters to allow the instruments to restart the months-long process of cooling to final temperatures.

When NIRCam reaches 120 kelvins (approximately -244 degrees Fahrenheit, or -153 degrees Celsius), Webb’s optics team will be ready to begin meticulously moving the 18 primary mirror segments to form a single mirror surface. The team has selected the star HD 84406 as its target to begin this process. It will be the first object NIRCam “sees” when photons of light hit the instrument’s powered-on detectors. The process will essentially create an image of 18 random, blurry points of light. For the first few weeks of mirror alignment, the team will keep the instrument trained on the star while they make microscopic adjustments to the mirror segments; ultimately that collection of 18 blurry dots will become a focused image of a single star. Cooling of the telescope and instruments will also continue over the next month, with the near-infrared instruments ultimately reaching 37-39 kelvins. The cryocooler will cool MIRI to 6 kelvins in the following months.

The Webb Team Looks Back on Successful Deployments

The big news for Webb this week was the final insertion into orbit around the second Lagrange point. The team also turned on the High-Gain Antenna, enabling downlink to Earth through the Deep Space Network using the Ka radio band. The Ka-band provides a much higher data rate than the S-band that Webb has been using for communications up until now. The Ka-band and the High-Gain Antenna will eventually allow the observatory to send all of the science images and data down to the ground for astronomers around the world to analyze and make discoveries.

As we look back on Webb’s first month in space, we asked Bill Ochs, Webb project manager, to share with us his thoughts on the mission so far:

“It has been about a month since launch, and it has been an unbelievable ride. I am so filled with pride for our team. The deployments could not have gone more perfectly. After the last wing deployment, more than one person made comments like, ‘it seemed so simple; did we overstate the complexity and difficulty of the deployments?’ The perfection of the deployment execution and the subsequent activities reflects directly on how hard everyone worked and the diligence and sacrifice it took on the part so many people. The fact that it looked simple is a tribute to all those over the years who have worked towards Webb mission success. We are now ready to align mirrors and commission instruments and have already proven that all the hardware associated with the optics (including 132 actuators) is working beautifully. By the time we get to instrument commissioning, we are going to have one hell of a telescope. Finally, our ops team and ground system have done a fantastic job of executing the commissioning timeline, and all those rehearsals have paid off. As folks on Webb know, I’m a pretty big Jimmy Buffett fan (understatement – I’m a parrot head). Driving around today, the song ‘Book On The Shelf’ came on, and this verse (particularly the third line, and I changed the fifth line) just shouted the JWST team to me.

And I know these stories were sailed way before me
Toss a note in a bottle and hope that it helps
I’m so damn lucky to have an all-star crew
Some stoic, some crazy, some just passin’ through
I know I’m so privileged to work with the best and
I’m all done explaining or passin’ some test
So pour me another, it’s good for my health
I’m not ready to put the book on the shelf

“Thanks to the Webb team for everything you have done and continue to do.”

—Bill Ochs, Webb project manager, NASA’s Goddard Space Flight Center

Next up: HD 84406! That is the first star Webb will point at to gather engineering data to start the mirror alignment process. The team chose a bright star (magnitude 6.7 at a distance of about 260 light-years, as measured by Gaia). The star is a sun-like G star in the Ursa Major constellation, which can be seen by Webb at this time of the year. This is just the first step; HD 84406 will be too bright to study with Webb once the telescope starts to come into focus. But for now, it is the perfect target to begin our search for photons, a search that will lead us to the distant universe.

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Alexandra Lockwood, project scientist for Webb science communications, Space Telescope Science Institute

Orbital Insertion Burn a Success, Webb Arrives at L2

Today, at 2 p.m. EST, Webb fired its onboard thrusters for nearly five minutes (297 seconds) to complete the final postlaunch course correction to Webb’s trajectory. This mid-course correction burn inserted Webb toward its final orbit around the second Sun-Earth Lagrange point, or L2, nearly 1 million miles away from the Earth.

The final mid-course burn added only about 3.6 miles per hour (1.6 meters per second) – a mere walking pace – to Webb’s speed, which was all that was needed to send it to its preferred “halo” orbit around the L2 point.

“Webb, welcome home!” said NASA Administrator Bill Nelson. “Congratulations to the team for all of their hard work ensuring Webb’s safe arrival at L2 today. We’re one step closer to uncovering the mysteries of the universe. And I can’t wait to see Webb’s first new views of the universe this summer!”

Webb trajectory diagram
Click on the trajectory diagram for a full-screen version. Credit: Steve Sabia/NASA Goddard

Webb’s orbit will allow it a wide view of the cosmos at any given moment, as well as the opportunity for its telescope optics and scientific instruments to get cold enough to function and perform optimal science. Webb has used as little propellant as possible for course corrections while it travels out to the realm of L2, to leave as much remaining propellant as possible for Webb’s ordinary operations over its lifetime: station-keeping (small adjustments to keep Webb in its desired orbit) and momentum unloading (to counteract the effects of solar radiation pressure on the huge sunshield).

“During the past month, JWST has achieved amazing success and is a tribute to all the folks who spent many years and even decades to ensure mission success,” said Bill Ochs, Webb project manager at NASA’s Goddard Space Flight Center. “We are now on the verge of aligning the mirrors, instrument activation and commissioning, and the start of wondrous and astonishing discoveries.”

Now that Webb’s primary mirror segments and secondary mirror have been deployed from their launch positions, engineers will begin the sophisticated three-month process of aligning the telescope’s optics to nearly nanometer precision.

Watch a special episode of NASA Science Live at 3 p.m. EST today to learn more about what’s next for the James Webb Space Telescope.

Webb’s Journey to L2 Is Nearly Complete

On Monday, Jan. 24, engineers plan to instruct NASA’s James Webb Space Telescope to complete a final correction burn that will place it into its desired orbit, nearly 1 million miles away from the Earth at what is called the second Sun-Earth Lagrange point, or “L2” for short.

Mathematically, Lagrange points are solutions to what is called the “restricted three-body problem.” Any two massive, gravitationally significant objects in space generate five specific locations – Lagrange points – where their gravitational forces and the centrifugal force of the motion of a small, third body such as a spacecraft are in equilibrium. Lagrange points are labeled L1 through L5 and are preceded by the names of the two gravitational bodies that generate them (the big one first).

Sun-Earth Lagrange Point 2
Source: NASA/WMAP Science Team

While all Lagrange points are gravitational balance points, not all are completely stable. L1, L2, and L3 are “meta-stable’ locations with saddle-shaped gravity gradients, like a point on the middle of a ridgeline between two slightly higher peaks wherein it is the low, stable point between the two peaks, but it is still a high, unstable point relative to the valleys on either side of the ridge. L4 and L5 are stable in that each location is like a shallow depression or bowl atop the middle of a long, tall ridge or hill.

So why send Webb to orbit Sun-Earth L2? Because it is an ideal location for an infrared observatory. At Sun-Earth L2, the Sun and Earth (and Moon, too) are always on one side of space, allowing Webb to keep its telescope optics and instruments perpetually shaded. This enables them to get cold for infrared sensitivity, yet still access nearly half the sky at any given moment for observations. To view any and every point in the sky over the course of time requires merely waiting a few months to travel farther around the Sun and reveal more of the sky that was previously “behind” the Sun.

Moreover, at L2, Earth is far enough away that the roughly room-temperature heat radiating from it won’t warm up Webb. And because L2 is a location of gravitational equilibrium, it is easy for Webb to maintain an orbit there. Note that it is simpler, easier, and more efficient to orbit around L2 than to dwell precisely at L2. Furthermore, by orbiting rather than being exactly at L2, Webb will never have the Sun eclipsed by Earth, which is necessary for Webb’s thermal stability and for power generation. In fact, Webb’s orbit around L2 is larger in size than the Moon’s orbit around Earth! L2 is also convenient for always maintaining contact with the Mission Operations Center on Earth through the Deep Space Network. Other space-based observatories including WMAP, Herschel, and Planck orbit Sun-Earth L2 for the same reasons.

Generally speaking, getting a spacecraft to Sun-Earth L2 is fairly straightforward, but Webb’s architecture added a wrinkle. Karen Richon, Webb’s Flight Dynamics lead engineer, describes getting Webb to L2 and keeping it there:

“Think about throwing a ball straight up in the air, as hard as you can; it starts out very fast, but slows down as gravity pulls it back towards Earth, eventually stopping at its peak and then returning to the ground. Similar to your arm giving the ball energy to go up a few meters from the Earth’s surface, the Ariane 5 rocket gave Webb energy to go the great distance of 1.1 million kilometers, but not quite enough energy to escape Earth’s gravity. Just like the ball, Webb is slowing down, and, if we allowed it, would eventually stop and fall back towards Earth. Unlike the ball, Webb wouldn’t return to the Earth’s surface, but would be in an extremely elliptical orbit, with a perigee altitude of 300 kilometers and an apogee altitude of 1,300,000 kilometers. Utilizing thrust every three weeks or so from small rocket engines aboard Webb will keep it orbiting L2, looping around it in a halo orbit once every six months.

“So, why did the Ariane not give Webb more energy and why did Webb need course correction? If the Ariane had given Webb even a little bit too much energy than needed to get it to L2, it would be going too fast when it got there and would overshoot its desired science orbit. Webb would have to do a significant braking maneuver by thrusting toward the Sun to slow down. Not only would that big burn cost a lot of propellant, it would be impossible because it would require Webb to turn 180 degrees in order to thrust toward the Sun, which would have exposed its telescope optics and instruments directly to the Sun, thus overheating their structures and literally melting the glue that holds them together. Mounting thrusters on the telescope as a way to direct braking thrust was infeasible for a number of reasons and was never a design option.

“Therefore, Webb requested just enough energy from the Ariane rocket to ensure that we would never have to do a retro burn, but would always require a burn from the observatory to precisely make up the difference and place it in the desired orbit. The Ariane 5 targeted Webb so accurately that our first and most critical burn was smaller than we had to plan and design for, leaving more fuel for an extended mission!”

—Karen Richon, Webb Flight Dynamics lead engineer, NASA’s Goddard Space Flight Center

A detailed breakdown of Webb’s orbit can be found here.

By Thaddeus Cesari, Webb science writer, NASA’s Goddard Space Flight Center, Greenbelt, Md.

Webb Mirror Segment Deployments Complete

Editor’s Note: This post was updated to clarify the strength vs. stiffness of beryllium.

Last week, the Webb team began moving the observatory’s individual mirror segments out of their launch positions. Today, we hear from Erin Wolf, Webb program manager at Ball Aerospace, about the completion of that process:

“Today, the James Webb Space Telescope team completed the mirror segment deployments. As part of this effort, the motors made over a million revolutions this week, controlled through 20 cryogenic electronics boxes on the telescope. The mirror deployment team incrementally moved all 132 actuators located on the back of the primary mirror segments and secondary mirror. The primary mirror segments were driven 12.5 millimeters away from the telescope structure. Using six motors that deploy each segment approximately half the length of a paper clip, these actuators clear the mirrors from their launch restraints and give each segment enough space to later be adjusted in other directions to the optical starting position for the upcoming wavefront alignment process. The 18 radius of curvature (ROC) actuators were moved from their launch position as well. Even against beryllium’s bending stiffness per weight, which is six times greater than that of ordinary steel, these ROC actuators individually shape the curvature of each mirror segment to set the initial parabolic shape of the primary mirror.

“Next up in the wavefront process, we will be moving mirrors in the micron and nanometer ranges to reach the final optical positions for an aligned telescope. The process of telescope alignment will take approximately three months.”

—Erin Wolf, James Webb Space Telescope Program Manager, Ball Aerospace

Mirror, Mirror…On Its Way!

With major deployments complete, Webb continues its journey to its final halo orbit around L2. In the meantime, there are several smaller deployments in the next couple of weeks, which constitute the beginning of a several-month phase of aligning the telescope’s optics. This week, we have started the process of moving the mirror segments (all primary plus secondary) out of their stowed launch positions. For more details, here is Marshall Perrin from the Space Telescope Science Institute, home of the Webb Mission Operations Center:

“To support the movable mirrors during the ride to space, each of them has on its back three rigid metal pegs which can nestle into matching holder sockets in the telescope structure. Before launch, the mirrors were all positioned with the pegs held snug in the sockets, providing extra support. (Imagine Webb holding its mirrors tucked up close to its telescope structure, keeping them extra safe during the vibrations and accelerations of launch.) Each mirror now needs to be deployed out by 12.5 millimeters (about half an inch) to get the pegs clear from the sockets. This will give the mirrors ‘room to roam’ and let them be readied in their starting positions for alignment.

“Getting there is going to take some patience: The computer-controlled mirror actuators are designed for extremely small motions measured in nanometers. Each of the mirrors can be moved with incredibly fine precision, with adjustments as small as 10 nanometers (or about 1/10,000th of the width of a human hair). Now we’re using those same actuators instead to move over a centimeter. So these initial deployments are by far the largest moves Webb’s mirror actuators will ever make in space.

“And we don’t do them all at once. The mirror control system is designed to operate only one actuator at a time. That way is both simpler (in terms of the complexity of the control electronics) and safer (since computers and sensors can closely monitor each individual actuator as it works). Furthermore, to limit the amount of heat put into Webb’s very cold mirrors from the actuator motors, each actuator can only be operated for a short period at a time. Thus, those big 12.5-millimeter moves for each segment are split up into many, many short moves that happen one actuator at a time. Scripts sent from the Mission Operations Center will direct this process under human supervision, slowly and steadily moving one actuator at a time, taking turns between segments. At full speed, it takes about a day to move all the segments by just 1 millimeter. It’s about the same speed at which grass grows!

“This may not be the most exciting period of Webb’s commissioning, but that’s OK. We can take the time. During the days that we’re slowly deploying the mirrors, those mirrors are also continuing to slowly cool off as they radiate heat away into the cold of space. The instruments are cooling, too, in a gradual and carefully controlled manner, and Webb is also continuing to gently coast outwards toward L2. Slow and steady does it, for all these gradual processes that get us every day a little bit closer to our ultimate goal of mirror alignment.”

—Marshall Perrin, deputy telescope scientist, Space Telescope Science Institute

Webb Begins Its Months-Long Mirror Alignment

Webb has begun the detailed process of fine-tuning its individual optics into one huge, precise telescope.

Engineers first commanded actuators – 126 devices that will move and shape the primary mirror segments, and six devices that will position the secondary mirror – to verify that all are working as expected after launch. The team also commanded actuators that guide Webb’s fine steering mirror to make minor movements, confirming they are working as expected. The fine steering mirror is critical to the process of image stabilization.

Ground teams have now begun instructing the primary mirror segments and secondary mirror to move from their stowed-for-launch configuration, off of snubbers that kept them snug and safe from rattling from vibration. These movements will take at least ten days, after which engineers can begin the three-month process of aligning the segments to perform as a single mirror.

Following the Next Steps in Webb’s Journey

After two weeks of complex structural deployments, Webb has passed a major milestone and is now fully unfolded in space. For insight on what to expect in the months ahead and how to follow along, we hear from Alexandra Lockwood, project scientist for Webb science communications at the Space Telescope Science Institute:

“Words can’t describe the pride and excitement the Webb team is feeling right now. From engineers to scientists to IT staff to graphic designers to administrative personnel (and more!), we are all overjoyed with the incredible successes of the observatory to date. While we still have a long way to go before getting the science, the engineering feats that have been accomplished, on Earth and now in space, are awe-inspiring. They are a testament to the hard work and expertise of the international Webb team.

“Now that the action-packed deployment sequence is over, we are moving into a much slower, yet deliberate, phase of the commissioning process. In the next two weeks, we will move each of the 18 primary mirror segments, and the secondary mirror, out of their launch positions. Then five months of commissioning will include 1) further cooling of the entire observatory, and of the Mid-Infrared Instrument in particular, 2) checking and then aligning the secondary and 18 mirror segments into a single coherent optical system, first with the NIRCam instrument and then with all instruments individually and in parallel, and 3) calibrating of each of the four instruments and their many scientific modes. The novelty and variety of science that this observatory can produce requires thousands of things to be checked ahead of time. But rest assured that this summer will sizzle with the hot (nay cold?) observations we will soon be sharing!

“The team is committed to keeping you informed – even through the often slow and meticulous parts of this commissioning process. This blog will be updated weekly, and sometimes more often. Please check back to hear more status updates, in-depth explanations of Webb’s science and technology, and even some fun team anecdotes!

“We’re excited to be on this journey to #UnfoldTheUniverse with you.”

—Alexandra Lockwood, project scientist for Webb science communications, Space Telescope Science Institute