James Webb Space Telescope

The Mid-Infrared Instrument (MIRI) on NASA’s James Webb Space Telescope is now cooled by a gaseous helium cryocooler to under 7 kelvins. With the cooler in its final state, the Webb team is operating the MIRI instrument this week as part of seventh and final stage of the telescope alignment. When the instrument is operating, the detectors and electronics produce heat, which is balanced by the cryocooler to keep MIRI at a stable, and very cold, operating temperature. The near-infrared instruments also warm up during operations and have to dissipate heat, although for these instruments this is done with passive cooling; the heat from the detectors and electronics is radiated into deep space.

Now that the instruments are at their operating temperatures, the telescope mirrors will also continue cooling down to their final temperatures, but they are not quite there yet. The primary mirror segments and the secondary mirror are made of beryllium (coated with gold). At cryogenic temperatures, beryllium has a long thermal time constant, which means that it takes a long time to cool or to heat up. The primary mirror segments are still cooling, very slowly.

The secondary mirror, hanging out on the end of its support structure a long way from any heat sources, is the coldest mirror, currently at 29.4 kelvins. The 18 primary mirror segments range in temperature from 34.4 kelvins to 54.5 kelvins. An advantage of beryllium mirrors is that they don’t change shape with temperature the way glass mirrors would at these temperatures, so the temperature range does not affect the telescope alignment process.

Currently, four of the 18 mirror segments are above 50 kelvins: at 52.6, 54.2, 54.4, and 54.5. These four mirror segments emit some mid-infrared light that reaches the MIRI detectors. Since all the mirror temperatures are now below 55 kelvins, it is expected that MIRI will be sensitive enough to perform its planned science, but any additional cooling of these mirrors will only enhance its performance. The Webb team hopes to see the mirrors cool by an additional 0.5 to 2 kelvins.

When we point the telescope at an astronomical target, the telescope and sunshield move together. The angle that the sunshield presents to the Sun is called the pointing “attitude.” The tiny amount of residual heat that makes its way through the five-layer sunshield to the primary mirror depends on this attitude, and since the mirror segment temperatures change very slowly, their temperatures depend on the attitude averaged over multiple days.

During commissioning, Webb is currently spending most of its time pointed at the ecliptic poles, which is a comparatively hot attitude. During science operations, starting this summer, the telescope will have a much more even distribution of pointings over the sky. The average thermal input to the warmest mirror segments is expected to go down a bit, and the mirrors will cool a bit more.

Later in commissioning, we plan to test the thermal dependence of the mirrors on the attitude. We will point Webb at a hot attitude for several days, and point Webb at a cold attitude for several days, in a process called the thermal slew. This will inform us how long it takes for the mirrors to cool down or heat up when the observatory is at these positions for any given amount of time.

Is Webb at its final temperature? The answer is: almost!

---

–Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

The journey of commissioning the Webb telescope continues this week with the successful cooling of the Mid-InfraRed Instrument (MIRI), through the critical ‘pinch point,’ down to its final operating temperature of less than 7 kelvins (-447 degrees Fahrenheit, or -266 degrees Celsius). This was a precondition to completing the seventh and final stage of the mirror alignment process.  The next steps include initial check-outs of MIRI and continue on to the final stages of multi-instrument, multi-field alignment with all four science instruments.

Last week we shared the cool science on star and planet formation planned for Webb. Today, we get into details on how Webb will study planets around other stars, which are known as extrasolar planets, or exoplanets. Knicole Colón, Webb’s deputy project scientist for exoplanet science, takes us into the discovery space of exploring new worlds beyond our solar system. Dr. Colón brings a unique perspective as she is also the project scientist for the Transiting Exoplanet Survey Satellite (TESS), a mission that has found many exoplanet targets that Webb will observe.

“Over the last 30 years, astronomers have discovered over 5,000 extrasolar planets. These discoveries have revealed that exoplanets span a vast range of masses, sizes, and temperatures and orbit all types of stars, leading to extraordinarily diverse worlds.

“With its powerful spectroscopic and imaging capabilities across a wide infrared wavelength range, Webb is poised to revolutionize our knowledge of the composition of these worlds and of planet-forming disks. From small, potentially rocky exoplanets up to giant, gaseous ones, Webb will observe these worlds with the transit technique. Direct imaging techniques will be used to study young, giant exoplanets along with the environments in which planets form and evolve around stars, known as protoplanetary disks and debris disks.

“One specific exoplanet observation that will be done with Webb involves collecting observations over the course of a planet’s orbit to enable measurements of the atmospheric composition and dynamics. I am involved in a program to observe the gas giant HD 80606 b as part of Webb’s first year of observations. Because the orbit of HD 80606 b is extremely eccentric (non-circular) and long (111 days), the amount of energy received by the planet from its star ranges from approximately 1 to 950 times what Earth receives from the Sun! This results in extreme temperature variations, which are predicted to cause clouds to rapidly form and dissipate in the planet’s atmosphere on very short timescales. Our science team will probe these predicted cloud dynamics in real-time over the course of a continuous ~18 hour observation of HD 80606 b as it passes behind its star, using the NIRSpec instrument on Webb to measure thermal light from the planet’s atmosphere.

“Beyond gas giants, a number of Webb’s exoplanet targets in its first year of observations are small and orbit stars that are smaller and cooler than the Sun, known as M dwarfs. While exoplanet discovery began around 30 years ago, many of these small exoplanets around M dwarfs were just discovered in the last few years by surveys like TESS. Webb observations will start to reveal the diversity of atmospheres that exist on these small planets by searching for evidence of molecules like water, carbon dioxide, and methane in their atmospheres. Because M dwarfs are typically much more active than the Sun and have energetic stellar flares that could potentially strip the atmospheres off of these planets, Webb observations may even reveal that some of these small planets have no atmosphere at all.

“With TESS and other surveys continuing to discover additional planets in our galaxy at a regular pace and Webb preparing to study the atmospheres of many of these newly discovered worlds, our exoplanet adventures are in many ways just beginning.”

– Knicole Colón, Webb’s deputy project scientist for exoplanet science, NASA’s Goddard Space Flight Center

---

Stefanie Milam, Webb deputy project scientist for planetary science, NASA Goddard

Jonathan Gardner, Webb deputy senior project scientist, NASA Goddard

 

The ongoing success of the multi-instrument optics alignment for NASA’s Webb telescope’s near-infrared instruments has moved the attention of the commissioning team to chill as we carefully monitor the cooling of the Mid-InfraRed Instrument (MIRI) down to its final operating temperature of less than 7 kelvins (-447 degrees Fahrenheit, or -266 degrees Celsius). We are continuing other activities during this slow cooldown which include monitoring the near-infrared instruments. As MIRI cools, other major components of the observatory, such as the backplane and mirrors, also continue to cool and are approaching their operational temperatures.

Last week, the Webb team did a station-keeping thruster burn to maintain Webb’s position in orbit around the second Lagrange point. This was the second burn since Webb’s arrival at its final orbit in January; these burns will continue periodically throughout the lifetime of the mission.

In the last few weeks, we have been sharing some of Webb’s anticipated science, beginning with the study of the first stars and galaxies in the early universe. Today, we will see how Webb will peer within our own Milky Way galaxy at places where stars and planets form. Klaus Pontoppidan, the Space Telescope Science Institute project scientist for Webb, shares the cool science planned for star and planet formation with Webb:

“In the first year of science operations, we expect Webb to write entirely new chapters in the history of our origins – the formation of stars and planets. It is the study of star and planet formation with Webb that allows us to connect observations of mature exoplanets to their birth environments, and our solar system to its own origins. Webb’s infrared capabilities are ideal for revealing how stars and planets form for three reasons: Infrared light is great at seeing through obscuring dust, it picks up the heat signatures of young stars and planets, and it reveals the presence of important chemical compounds, such as water and organic chemistry.

“Let us look at each reason in more detail. We often hear that infrared light passes through obscuring dust, revealing newborn stars and planets that are still embedded in their parental clouds. In fact, mid-infrared light, as seen by MIRI, can pass through 20 times thicker clouds than visible light. Because young stars are formed quickly (by cosmic standards, anyway) – in as little as a few 100,000 years – their natal clouds have not had time to disperse, hiding what is going on in this critical stage from visible view. Webb’s infrared sensitivity allows us to understand what happens at these very first stages, as gas and dust are actively collapsing to form new stars.

“The second reason has to do with the young stars and giant planets themselves. Both begin their lives as large, puffy structures that contract over time. While young stars tend to get hotter as they mature, and giant planets cool, both typically emit more light in the infrared than at visible wavelengths. That means that Webb is great at detecting new young stars and planets and can help us understand the physics of their earliest evolution. Previous infrared observatories, like the Spitzer Space Telescope, used similar techniques for the nearest star-forming clusters, but Webb will discover new young stars across the galaxy, the Magellanic Clouds, and beyond.

“Finally, the infrared range (sometimes called the “molecular fingerprint region”) is ideal for identifying the presence of a range of chemicals, in particular water and various organics. All four of Webb’s science instruments can detect various important molecules using their spectroscopic modes. They are particularly sensitive to molecular ices present in cold molecular clouds before stars are formed, and NIRCam and NIRSpec will, for the first time, comprehensively map the spatial distribution of ices to help us understand their chemistry. MIRI will also observe warm molecular gas near many young stars where rocky, potentially habitable planets may be forming. These observations will be sensitive to most bulk molecules and will allow us to develop a chemical census at the earliest stages of planet formation. It is no surprise that a significant number of Webb’s early scientific investigations aim to measure how planetary systems build the molecules that may be important for the emergence of life as we know it.

“We will be keeping a close eye on MIRI as it cools down. As the only mid-infrared instrument on Webb, MIRI will be particularly important for understanding the origins of stars and planets.”

–Klaus Pontoppidan, Webb project scientist, Space Telescope Science Institute

---

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Stefanie Milam, Webb deputy project scientist for planetary science, NASA Goddard

“The Mid-Infrared Instrument (MIRI) and other Webb instruments have been cooling by radiating their thermal energy into the dark of space for the bulk of the last three months. The near-infrared instruments will operate at about 34 to 39 kelvins, cooling passively. But MIRI’s detectors will need to get a lot colder still, to be able to detect longer wavelength photons. This is where the MIRI cryocooler comes in.

“Over the last couple weeks, the cryocooler has been circulating cold helium gas past the MIRI optical bench, which will help cool it to about 15 kelvins. Soon, the cryocooler is about to experience the most challenging days of its mission. By operating cryogenic valves, the cryocooler will redirect the circulating helium gas and force it through a flow restriction. As the gas expands when exiting the restriction, it becomes colder, and can then bring the MIRI detectors to their cool operating temperature of below 7 kelvins. But first, the cryocooler must make it through the ‘pinch point’ – the transition through a range of temperatures near 15 kelvins, when the cryocooler’s ability to remove heat is at its lowest. Several time-critical valve and compressor operations will be performed in rapid succession, adjusted as indicated by MIRI cryocooler temperature and flow rate measurements. What is particularly challenging is that after the flow redirection, the cooling ability gets better as the temperature gets lower. On the flip side, if the cooling is not immediately achieved due to, for example, larger than modeled heat loads, MIRI will start warming.

“Once the cryocooler overcomes the remaining heat loads, it will settle into its lower-power steady science operation state for the rest of the mission. This pinch point event has been extensively practiced in the cryocooler testbed at NASA’s Jet Propulsion Laboratory (JPL), which manages the MIRI cryocooler, as well as during Webb testing at the agency’s Goddard Space Flight Center and Johnson Space Center. Performing it on orbit will be supported by the operations team comprised of personnel from JPL, Goddard, and the Space Telescope Science Institute. The MIRI cryocooler was developed by Northrop Grumman Space Systems. MIRI was developed as a 50/50 partnership between NASA and ESA (European Space Agency), with JPL leading the U.S. efforts and a multi-national consortium of European astronomical institutes contributing for ESA.”

– Konstantin Penanen and Bret Naylor, cryocooler specialists, NASA JPL

“MIRI stands out from Webb’s other instruments because it operates at much longer infrared wavelengths, compared to the other instruments that all begin with an ‘N’ for ‘near-infrared.’ MIRI will support the instrument suite to explore the infrared universe with depth and detail that are far beyond anything that has been available to astronomers to date.

“The imager promises to reveal astronomical targets ranging from nearby nebulae to distant interacting galaxies with a clarity and sensitivity far beyond what we’ve seen before. Our grasp on these glittering scientific treasures relies on MIRI being cooled to a temperature below the rest of the observatory, using its own dedicated refrigerator. Exoplanets at temperatures similar to Earth will shine most brightly in mid-infrared light. MIRI is therefore equipped with four coronagraphs, which have been carefully designed to detect such planets against the bright glare of their parent stars. The detailed colors of exo-giant planets (similar to our own Jupiter) can then be measured by MIRI’s two spectrometers to reveal chemical identities, abundances, and temperatures of the gases of their atmospheres (including water, ozone, methane, ammonia, and many more).

“Why so cold? MIRI’s state-of-the-art light sensitive detectors that are tuned to work in the mid-infrared are blind unless they are cooled below 7 kelvins (-266 degrees Celsius, or -447 degrees Fahrenheit). For contrast, a standard domestic freezer cools its contents to about 255 kelvins (-18 degrees Celsius, or -0.7 degrees Fahrenheit). At higher temperatures, any signal that may be detected from the sky is lost beneath the signal from its own internally generated ‘dark current.’ Even if the detectors are cooled, Webb images would still be swamped by the glow of thermal infrared light emitted by MIRI’s own mirrors and aluminum structure if they are to get warmer than 15 kelvins (-258 degrees Celsius, or -433 degrees Fahrenheit). The engineering solution was to stand MIRI off from the instrument mounting structure behind Webb’s primary mirror like a high-tech metal spider on six carbon fibre legs. These insulate MIRI from the much hotter telescope (where 45 kelvins, or -228 degrees Celsius/-379 degrees Fahrenheit, qualifies as hotter). The instrument’s body is also swathed in a shiny aluminum-coated thermal blanket, which reflects the radiant heat of its surroundings.

“Getting this instrument cold is one of the last major challenges faced by Webb before the MIRI team can truly relax, and passing through the cooler’s ‘pinch point’ will be the most daunting step in this challenge. At that time, the cooler will have pulled out almost all of the heat left in MIRI’s 100 kilograms (220 pounds) of metal and glass from that tropical launch day morning, three months ago. MIRI will be the last of Webb’s four instruments to open its eyes on the universe.”

– Alistair Glasse, Webb-MIRI Instrument Scientist, UK Astronomy Technology Centre
and Macarena Garcia Marin, MIRI Instrument and Calibration Scientist, ESA

The sixth stage of aligning NASA’s James Webb Space Telescope’s mirrors to its scientific instruments so they will create the most accurate and focused images possible has concluded. While the Mid-Infrared Instrument (MIRI) continues its cooldown, optics teams have successfully aligned the rest of the observatory’s onboard instruments to Webb’s mirrors. Previous alignment efforts were so accurate that the team concluded no additional adjustments to the secondary mirror are necessary until the seventh and final stage, which will involve MIRI when it has fully cooled.

“As a general rule, the commissioning process starts with coarse corrections and then moves into fine corrections. The early secondary mirror coarse corrections, however, were so successful that the fine corrections in the first iteration of Phase Six were unnecessary,” said Chanda Walker, Webb wavefront sensing and control scientist, Ball Aerospace. “This accomplishment was due to many years of planning and great teamwork among the wavefront sensing team.”

Throughout the majority of the alignment process, Webb’s 18 hexagonal mirrors and secondary mirror were focused into alignment to the Near-Infrared Camera (NIRCam) instrument only. Upon completing this most recent step, the observatory is now aligned to the Fine Guidance Sensor (FGS), the Near-Infrared Slitless Spectrograph (NIRISS), and the Near-Infrared Spectrometer (NIRSpec) as well as NIRCam.

Once MIRI fully cools to its cryogenic operating temperature in the weeks ahead, a second multi-instrument alignment will occur to make final adjustments to the instruments and mirrors if needed. When the telescope is fully aligned and able to deliver focused light to each instrument, a key decision meeting will occur to confirm the end of aligning the James Webb Space Telescope. The team will then transition from alignment efforts to commissioning each instrument for scientific operations, which are expected to begin this summer.

While telescope alignment continues, Webb’s Mid-Infrared Instrument (MIRI) is still in cooldown mode. MIRI, which will be the coldest of Webb’s four instruments, is the only instrument that will be actively cooled by a cryogenic refrigerator, or cryocooler. This cryocooler uses helium gas to carry heat from MIRI’s optics and detectors out to the warm side of the sunshield. To manage the cooldown process, MIRI also has heaters onboard, to protect its sensitive components from the risk of ice forming. The Webb team has begun progressively adjusting both the cryocooler and these heaters, to ensure a slow, controlled, stable cooldown for the instrument. Soon, the team will turn off MIRI’s heaters entirely, to bring the instrument down to its operating temperature of less than 7 kelvins (-447 degrees Fahrenheit, or -266 degrees Celsius).

In the meantime, after achieving alignment with the Near-Infrared Camera (NIRCam), Webb engineers have begun aligning the telescope to the remaining near-infrared instruments. For more about this six-week process, we hear today from Michael McElwain and Charles Bowers, members of the Webb team at NASA’s Goddard Space Flight Center:

“Webb’s alignment at the NIRCam field showed some spectacular diffraction-limited images, producing a tantalizing glimpse of the capabilities this observatory will carry for its science program. This was a major milestone because it required nearly all of the observatory systems to be functioning as designed. It all worked as well as we dared to hope, and it was certainly a moment to celebrate.

“The next step is to ensure the telescope is well-aligned to the instruments other than NIRCam, including the guider (the Fine Guidance Sensor, or FGS) and the other three science instruments: the Near-Infrared Slitless Spectrograph (NIRISS), Near-Infrared Spectrometer (NIRSpec), and MIRI. All the near-infrared instruments have already been passively cooled, are approaching their operational temperatures, and are participating in this next alignment stage. MIRI requires active cooling by a cryocooler, which is now underway, and it will be ready for alignment in a few weeks.

“This is the sixth stage of our telescope alignment plan, the Telescope Alignment Over Instrument Fields of View. Each of the instruments occupies a part of the telescope focal plane, just slightly offset with respect to each other. NIRCam was intentionally placed at the center of the telescope field where the telescope’s optical performance is best due to its demanding imaging performance requirements. Additionally, NIRCam was equipped with some specialized optical tools used to align the telescope. However, the initial alignment using only NIRCam could lead to an incorrect placement that compensates errors from primary-to-secondary mirror misalignments with the primary mirror itself. Small misalignments of this type will be evident in images in instruments farther from the center of the telescope field of view.

“The first step was to simply look at star fields as seen by NIRCam, NIRISS, FGS, and NIRSpec to see whether they were in focus. The stars looked nearly in-focus, which was a sign that the primary to secondary mirror alignment was already very good. A more accurate optical error measurement has been carried out at five to 10 field positions within each operational science instrument, using data taken with the secondary mirror positioned out of focus. This dataset provided a conclusive determination of the telescope alignment state.

“The Webb optics team analyzed the multi-instrument dataset and determined that only minor focus adjustments are needed on the secondary mirror and science instruments. Since the telescope is still cooling along with the MIRI instrument, we will not apply the corrections at this time and will defer them until the next round.

“When MIRI is available, an additional round of measurements will be conducted by each science instrument to determine the final state of the telescope alignment. We will iterate this process as needed to ensure the telescope performance is optimized for all of the instruments. After the telescope alignment to all instruments is complete, we will transition to the final two months of commissioning, where we will carry out optical stability tests and measure the science instrument performance before embarking on the Cycle 1 science program.”

–Michael McElwain, Webb observatory project scientist, NASA Goddard

–Charles Bowers, Webb deputy observatory project scientist, NASA Goddard

 

After meeting the major milestone of aligning the telescope to NIRCam, the Webb team is starting to extend the telescope alignment to the guider (the Fine Guidance Sensor, or FGS) and the other three science instruments. This six-week-long process is called multi-instrument multi-field (MIMF) alignment.

When a ground-based telescope switches between cameras, sometimes the instrument is physically taken off the telescope, and a new one is installed during the daytime when the telescope is not in use. If the other instrument is already on the telescope, mechanisms are in place to move part of the telescope’s optics (known as a pick-off mirror) into the field of view.

On space telescopes like Webb, all the cameras see the sky at the same time; to switch a target from one camera to another, we repoint the telescope to put the target into the field of view of the other instrument.

After MIMF, Webb’s telescope will provide a good focus and sharp images in all the instruments. In addition, we need to precisely know the relative positions of all the fields of view. Over last weekend, we mapped the positions of the three near-infrared instruments relative to the guider and updated their positions in the software that we use to point the telescope. In another instrument milestone, FGS recently achieved “fine guide” mode for the first time, locking onto a guide star using its highest precision level. We have also been taking “dark” images, to measure the baseline detector response when no light reaches them – an important part of the instrument calibration.

Webb’s mid-infrared instrument, MIRI, will be the last instrument that is aligned, as it is still waiting for the cryogenic cooler to chill it to its final operating temperature, just under 7 degrees above absolute zero. Interspersed within the initial MIMF observations, the two stages of the cooler will be turned on to bring MIRI to its operating temperature. The final stages of MIMF will align the telescope for MIRI.

You might be wondering: If all of the instruments can see the sky at the same time, can we use them simultaneously? The answer is yes! With parallel science exposures, when we point one instrument at a target, we can read out another instrument at the same time. The parallel observations don’t see the same point in the sky, so they provide what is essentially a random sample of the universe. With a lot of parallel data, scientists can determine the statistical properties of the galaxies that are detected. In addition, for programs that want to map a large area, much of the parallel images will overlap, increasing the efficiency of the valuable Webb dataset.

---

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Stefanie Milam, Webb deputy project scientist for planetary science, NASA Goddard

This week the Webb team continued to make progress in aligning the telescope to the NIRCam instrument. Between taking the data to understand the optical components, we continue to check out the science instruments. The NIRSpec instrument includes a microshutter array of a quarter-million miniature movable windows, each 0.1 by 0.2 millimeters in size. The microshutter array allows scientists to target specific galaxies in fields they are studying, while closing the windows on the background or other objects which would contaminate the spectra. We have begun testing the mechanism and electronics that control and actuate the microshutters.

In recent weeks, we shared a technique for theoretically modeling the early universe. Today, we will discuss an observational program to help us answer some of those questions. Massimo Stiavelli, the Webb Mission Office head at the Space Telescope Science Institute, tells us about his planned investigations of the first stars and galaxies:

“The chemical composition of the early universe, just after the big bang, is the product of the nuclear processes that took place in the first few minutes of the universe’s existence. These processes are known as ‘primordial nucleosynthesis.’ One of the predictions of this model is that the chemical composition of the early universe is largely hydrogen and helium. There were only traces of heavier elements, which formed later in stars. These predictions are compatible with observations, and are in fact one of the key pieces of evidence that support the hot big bang model.

“The earliest stars formed out of material with this primordial composition. Finding these stars, commonly dubbed as the ‘First Stars’ or ‘Population III stars,’ is an important verification of our cosmological model, and it is within reach of the James Webb Space Telescope. Webb might not be able to detect individual stars from the beginning of the universe, but it can detect some of the first galaxies containing these stars.

“One way to confirm whether we are finding the first stars is to accurately measure metallicities of very distant galaxies. The astronomical term, metallicity, is a measurement of the amount of material heavier than hydrogen and helium – so a low metallicity galaxy would indicate it was made up of these ‘First Stars.’ One of the most distant galaxies discovered so far, known as MACS1149-JD1, is confirmed to be at redshift 9.1 and emitted the light we see when the universe was only 600 million years old. The light from this distant galaxy has been traveling ever since then and is just reaching us now.

“In the first year of Webb science, I have an observing program to study this galaxy and determine its metallicity. I will do this by attempting to measure the ratio in the strength of two spectroscopic lines emitted by oxygen ions, originally emitted at violet-blue and blue-green visible light (rest frame wavelengths at 4,363 angstroms and 5,007 angstroms). Thanks to cosmological redshift, these lines are now detectable at the infrared wavelengths that Webb can see. The use of a ratio of two lines of the same ion can provide an exquisite measurement of the gas temperature in this galaxy and, through relatively simple theoretical modeling, will provide a robust measurement of its metallicity.

“The challenge is that one of these lines is usually extremely weak. However, this line tends to get stronger at lower metallicity. So if we failed to detect the line and measure metallicity for MACS1149-JD1, that would likely mean that it has already been enriched by the heavier elements, and we need to look further and harder. Whether using my data or with future programs, I fully expect that during its operational lifetime Webb will be able to find objects with metallicity sufficiently low to hold keys for understanding the first generation of stars.”

–Massimo Stiavelli, Webb Mission Office head, Space Telescope Science Institute

---

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Alexandra Lockwood, project scientist for Webb science communications, Space Telescope Science Institute

This week, the Webb team has been working on the fourth stage of mirror alignment, called Coarse Phasing, which measures and corrects smaller height differences between the mirror segments.

In the meantime this past week, Webb’s Near-Infrared Spectrograph (NIRSpec) team successfully finished the check-out and initial characterization of three crucial onboard mechanisms. Today, members of the team join us to share more about the inner workings of this instrument, which was contributed by ESA (European Space Agency):

“To work properly as a spectrograph, NIRSpec has three mechanisms: a Filter Wheel Assembly (FWA), a Grating Wheel Assembly (GWA), and a Refocus Mechanism Assembly (RMA). The gratings in the GWA spread the incoming light over its colors or wavelengths to make a spectrum. The filters in the FWA block the wavelengths that are outside the range of interest to prevent contamination between different optical paths, or ‘orders.’ The RMA adjusts the instrument focus.

“We operated the Filter Wheel Assembly first, cycling it through all eight of its positions in both forward and reverse directions. Those eight filter wheel positions include five long-pass order-separation filters, two finite-band target acquisition filters, and an ‘opaque’ position that serves as the instrument shutter. At each position, we recorded a set of reference data. This data showed us how well the wheel was moving and how accurately it settled into each position. Between each FWA position, we downloaded ‘high-capacity buffer’ data from the positioning sensors, and the NIRSpec team analyzed the data. The data showed that the wheel moved very well even in the first attempt.

“We then used a very similar procedure for the Grating Wheel Assembly, which also performed excellently the first time. The GWA is shaped like a miniature Ferris wheel and holds eight optical elements, consisting of six diffraction gratings, one prism, and a mirror. These dispersers separate the incoming light by wavelength, generating spectra that are detected by NIRSpec’s sensor chips.

“The Refocus Mechanism Assembly includes a linear translation stage that holds two flat mirrors. It will be used to fine-tune the instrument focus, compensating for any change in the overall focus position of the Webb telescope that may occur throughout the observatory’s lifetime. After various initial retrievals of the RMA telemetry acquisition chain, the mechanism was moved forward a few hundred steps from launch position. Just like with the FWA and GWA, we used high-capacity buffer readouts to collect reference datasets. After the initial move, we commanded the RMA mirrors to their previous best focus position; successful completions of this test showed us that the RMA is a well-behaved and healthy mechanism.

“In the coming months, the NIRSpec team will continue their commissioning efforts. The whole team is very much looking forward to the start of science observations this summer!”

–Maurice Te Plate, Webb NIRSpec systems engineer, European Space Agency; Tim Rawle, Webb NIRSpec instrument scientist, European Space Agency; and Ralf Ehrenwinkler, project manager, NIRSpec post-delivery support, Airbus Defence and Space

---

By Jonathan Gardner, Webb deputy senior project scientist, NASA’s Goddard Space Flight Center

And Alexandra Lockwood, project scientist for Webb science communications, Space Telescope Science Institute

Webb continues on its path to becoming a focused observatory. The team has successfully worked through the second and third out of seven total phases of mirror alignment. With the completion of these phases, called Segment Alignment and Image Stacking, the team will now begin making smaller adjustments to the positions of Webb’s mirrors.

After moving what were 18 scattered dots of starlight into Webb’s signature hexagonal formation, the team refined each mirror segment’s image by making minor adjustments, while also changing the alignment of Webb’s secondary mirror. The completion of this process, known as Segment Alignment, was a key step prior to overlapping the light from all the mirrors so that they can work in unison.

Once Segment Alignment was achieved, the focused dots reflected by each mirror were then stacked on top of each other, delivering photons of light from each segment to the same location on NIRCam’s sensor. During this process, called Image Stacking, the team activated sets of six mirrors at a time and commanded them to repoint their light to overlap, until all dots of starlight overlapped with each other.

“We still have work to do, but we are increasingly pleased with the results we’re seeing,” said Lee Feinberg, optical telescope element manager for Webb at NASA’s Goddard Space Flight Center. “Years of planning and testing are paying dividends, and the team could not be more excited to see what the next few weeks and months bring.”

Although Image Stacking put all the light from a star in one place on NIRCam’s detector, the mirror segments are still acting as 18 small telescopes rather than one big one. The segments now need to be lined up to each other with an accuracy smaller than the wavelength of the light.

The team is now starting the fourth phase of mirror alignment, known as Coarse Phasing, where NIRCam is used to capture light spectra from 20 separate pairings of mirror segments. This helps the team identify and correct vertical displacement between the mirror segments, or small differences in their heights. This will make the single dot of starlight progressively sharper and more focused in the coming weeks.